<< Click to Display Table of Contents >> Navigation: »No topics above this level« ZIP Rapid Deploy Range (HTML) |
SEE010, SEE015, SEE020, SEE030, SEE035 - Quick Start Guide
|
|
Full Instruction Manual http://www.cctvmanuals.com/manuals/SEE010_015_020_030_035/index.html |
The Rapid Deploy CCTV system is a fast and easy solution to provide CCTV protection. It consists of a 4Ch wireless receiver that plugs into a Zip NVR or DVR via its rear USB port.
Once the wireless receiver is plugged into the Zip NVR or DVR it enables it to see and record the wireless Rapid Deploy CCTV cameras.
Rapid Deploy is currently compatible with the ZIP Lite, ZIP Supa & ZIP Xtra DVR ranges (2 cameras only on a 4ch DVR) as well as 4, 8, 16, 32ch Zip NVRs. (Note it is not compatible with the ZIP SUPA-S range of recorders). Older Zip DVR/NVR models (up to 2019) may require a firmware upgrade.
How It Works
When the PIR is activated then the camera is activated and transmits data to the receiver.
At night time the light sensor is used to determine if the Infra-Red LEDs are also activated when the camera is activated by the PIR.
Two-way talk back can also be used when the camera is activated, using the Microphone on the front of the camera and the Built-in speaker. |
Powering the Cameras & Charging the Batteries
A rapid deploy battery pack is required to power the camera. The battery can be charged whilst it is inserted in the camera or the battery can be removed for charging.
Status LED:- Red = Charging Green = Charged (and plugged in) No Light = Not Charging |
|
SEE030 - Solar Panel The Rapid Deploy solar panel with Micro (B) USB lead can be used to charge the batteries.
|
A Micro (B) USB charger and lead is required for the charging the Rapid Deploy Batteries, these are not supplied. |
Mount the bracket (instead of the standard mounting plate. And slot the camera onto the plate. |
Mounting 1. Fix the mounting plate to the mounting surface using the screws and plugs provided.
2. Slot the camera onto the mounting plate from above.
|
|
NVR Pre-Setup - For PoE ZIP NVRs, the IP channel config needs altering first.
1. Go to the menu, Video > IP Channels 2. Video > IP Channels 3. Switch Mode > Set to Manual Mode 4. Then proceed with Channel Setup
|
Channel Setup - Setup the channels for USB Wireless.
1. Go to the menu, Video > Channel Config 2. In the DVR channel list > Select USB Wireless 3. Select Apply 4. The DVR will require a reboot once applied, click OK |
Pairing Overview - The cameras will need pairing, this can only be done in the menu on the recorder.
1. Go to the menu, Video > USB Wireless 2. Click Pair to start the pairing mode with the receiver 3. Select the Pair button on the rear of the camera |
4. Pairing successful! Displays once complete 5. Select Switch to ON 6. Click Apply |
Specifications
SEE010 |
SEE015 |
SEE020 |
|
Lens Type |
2.8mm Fixed Lens |
2.8mm Fixed Lens |
~ |
Viewing Angle |
120 Degrees |
120 Degrees |
~ |
Resolution |
HD 1080P / 2MP |
HD 1080P / 2MP |
Up to 2MP |
WiFi Range |
200m Max |
200m Max |
200m Max |
Audio |
2-Way Built-in |
2-Way Built-in |
Supported |
Audio Input |
Built-in Microphone |
Built-in Microphone |
Wireless from Camera |
Audio Output |
Built-in Speaker |
Built-in Speaker |
Via USB |
PIR |
Built-in 10m Range |
Built-in 10m Range |
~ |
InfraRed LEDs |
6 |
6 |
~ |
IR Range |
8m |
8m |
~ |
Min. Illumination |
0 Lux with LEDs on |
0 Lux with LEDs on |
~ |
Noise Reduction |
3D |
3D |
~ |
White Balance |
Auto |
Auto |
~ |
Power Source |
Battery Pack - 8700mAh (Supplied) |
Battery Pack - 8700mAh (Supplied) |
Powered from DVR/NVR |
Input Voltage |
DC 4.2V +-10% |
DC 4.2V +-10% |
~ |
Current Consumption |
420mA (Activate) / 400mA (Sleep) |
420mA (Activate) / 400mA (Sleep) |
~ |
Power Connection |
Micro USB (B) |
Micro USB (B) |
USB |
Finish |
White |
Black |
Black |
Build |
Plastic |
Metal |
Plastic |
Operating Temperature |
From -20 to 55 deg C |
From -20 to 55 deg C |
~ |
Use |
IP66 For External Use |
IP66 For External Use |
Internal Use Only |
Bracket |
Supplied |
Supplied |
Wall-Mount Fixings Supplied |
Dimensions |
(H) 136 x (W) 73 x (D) 89mm |
(H) 136 x (W) 73 x (D) 89mm |
(H) 25 x (W) 140 x (D) 60mm |
|
SEE030 |
Solar Cell |
Monocrystalline Silicon |
Solar Conversion Rate |
20% |
Maximum Power |
2.5W |
Voltage |
5.25V |
Current |
535mA |
Operating Temperature |
--30ºC ~ 70ºC |
Dimensions |
179mm (H) x 125mm (W) x 10mm (D) - without bracket |
Weight |
447g |
Build |
Plastic (black) |
Power Interface |
MIcro USB |
Cable Length |
360mm |
IP Rating |
IP66 |
Bracket |
Supplied - 360º Adjustable wall mount |