Intelbras IP cameras are widely used for home security, business surveillance, and professional monitoring systems. To configure or manage an Intelbras camera, users need to access the camera login page through a web browser or management software. The login process usually requires three important details such as Intelbras IP camera address, Administrator username and password.
This guide explains how to access an Intelbras IP camera, find the default IP address, check the default login credentials, reset forgotten passwords, and solve common login problems.
Expert Tip: Always change the factory default password after installing an Intelbras IP camera. The default credentials are intended for initial setup only and should not be used permanently.
Intelbras IP Camera Default Login Information
Before accessing your camera, you need the correct login details. Intelbras camera credentials depend on the model and manufacturing generation.
Default Intelbras IP Camera Username and Password
| Setting | Default Value |
|---|---|
| Username | admin |
| Password (older models) | admin |
| Password (some models) | 123456 |
Keep in mind that many new Intelbras devices require users to create an administrator password during the first installation. Therefore, a universal default password may not work on every camera.
What Is the Default IP Address of Intelbras IP Camera?
The most commonly used Intelbras IP camera default IP address is:
192.168.1.108
This IP address allows the user to open the camera configuration interface via a web browser for the first time and onwards.
Example:
http://192.168.1.108
However, the camera’s IP address can change automatically when:
- Your router automatically assigns IP addresses using DHCP.
- Someone previously configured the camera.
- The network environment has changed
If the default IP address doesn’t work, you’ll need to find the camera’s current IP address using the IP Utility software provided by the manufacturer.
How to Find Intelbras Camera IP Address?
There are several ways to locate your Intelbras camera on the network.
Method 1: Check Your Router
- Login to your router administration page.
- Open the connected devices list.
- Look for a device identified as Intelbras or an unknown IP camera.
- Copy the assigned IP address.
Method 2: Use Network Discovery Software
Network scanning tools such as IP Utility provided by manufacturers can identify devices connected to your local network.
This method helps when:
- The default IP address has changed.
- Multiple cameras are installed.
- The camera was configured by another user.
Method 3: Check Through Intelbras Recorder (NVR)
Usually the IP address of the new camera connected to the Intelbras NVR will display its IP address.
- Open the NVR menu.
- Go to camera management.
- View the connected camera information.
- Check the assigned IP address.
How to Login to Intelbras IP Camera Step by Step?
Follow these steps to access your Intelbras camera.
Step 1: Connect Your Camera
Make sure:
- The camera receives power.
- The Ethernet cable is connected properly.
- Your computer is connected to the same network.
For PoE cameras, confirm that the PoE switch or NVR provides enough power.
Step 2: Open a Web Browser
Use a modern browser such as:
- Google Chrome
- Microsoft Edge
- Firefox
Enter the camera IP address:
http://192.168.1.108
The Intelbras login page should appear.
Step 3: Enter Login Credentials
Example:
- Username: admin
- Password: admin
After successful login, you can configure:
- Camera resolution
- Recording settings
- Motion detection
- Network configuration
- User permissions
- Remote viewing options
Intelbras IP Camera Login Not Working? Try These Fixes
Login problems are common during installation or after network changes.
Problem 1: IP Address Cannot Be Opened
Possible causes:
- Wrong IP address
- Camera is on another network range
- Network cable issue
- IP conflict
Solutions:
- Restart the camera and router
- Check the router device list
- Scan the network for connected devices
- Confirm your computer and camera use the same subnet
Problem 2: Default Password Does Not Work
If “admin/admin” does not work, possible reasons include:
- The password was changed previously.
- The camera was already initialized.
- The device uses a first-time activation password.
Solution:
Reset the camera or use the official Intelbras recovery method based on your model.
Problem 3: Intelbras Camera Login Page Is Blank
Try:
- Clearing browser cache
- Using another browser
- Checking network connection
- Updating camera firmware
- Restarting the device
How to Reset Intelbras IP Camera Password?
If you forgot the administrator password, a factory reset may be required.
General reset procedure:
- Turn on the camera.
- Locate the reset button.
- Press and hold the button for around 10–15 seconds.
- Wait for the camera to restart.
- Perform the initial setup again.
A reset will remove:
- User accounts
- Network settings
- Camera configuration
- Recording preferences
Always confirm your camera model before performing a reset because reset procedures may vary.
How to Secure Intelbras Camera After Login?
After gaining access to your Intelbras IP camera, improve security with these steps:
Change the Default Password
Create a strong password containing:
- Uppercase letters
- Lowercase letters
- Numbers
- Special characters
Update Firmware Regularly
Firmware updates may improve:
- Security protection
- Device stability
- Compatibility
Avoid Using Default Credentials
Attackers often target cameras that still use factory passwords.
Never leave:
- Username: admin
- Password: admin
unchanged after installation.
Intelbras IP Camera Login FAQ
What is the default IP address for Intelbras IP cameras?
The most common default IP address is 192.168.1.108, but the actual address may vary depending on the network configuration and camera model.
What is the Intelbras camera default username?
The default username is usually admin.
What is the Intelbras default password?
Older models may use admin or 123456, while newer models may require creating a password during activation.
How do I access my Intelbras camera from a browser?
Connect the camera to your network, find its IP address, and enter the address into a browser:
http://camera-ip-address
How do I reset my Intelbras IP camera password?
You can usually reset the camera using the physical reset button or follow the recovery procedure provided for your specific model.
Final Thoughts
Accessing an Intelbras IP camera is straightforward when you have the correct IP address and login credentials. The default settings can help during initial installation, but every camera should be secured with a unique administrator password after setup.
If you cannot login, check the network connection, verify the camera IP address, and confirm whether the password has already been changed.
A properly configured Intelbras IP camera provides reliable monitoring while maintaining better protection against unauthorized access.
About This Guide
This guide was created based on common IP camera installation practices and network troubleshooting methods. Always verify settings with the official documentation for your exact Intelbras camera model, as features and login procedures may differ between devices.